openSUSE Leap Micro 6.1 Alpha

Leap Micro is an ultra-reliable, lightweight operating system built for containerized and virtualized workloads.

This community version is based on SUSE Linux Micro, which leverages the enterprise-hardened security and compliance components of SUSE Linux Enterprise. This merging of technologies provides for a modern, immutable, and developer-friendly OS platform.

Leap Micro since 6.0 offers a self-install image, a raw image, and a Packages DVD that can serve as an offline repository. The Self-install image is our recommendation for any USB-based installation since we no longer use traditional installers. Users can automate and customize their installation with either Ignition or Combustion or using the jeos-firstboot wizard. Give a try to Fuel Ignition our online Ignition config generator.

Try Leap Micro in VMs running on either Xen or KVM. Using a Raspberry Pi or other System on Chip hardware may use the preconfigured image. Both preconfigured and self-installed images are intended to be used with Combustion written to a USB, which is driven to allow configuration on any first boot, with the option for default password protected changes.

Download

A Short Leap Micro installation demo with combustion and cockpit.

Intel or AMD 64-bit desktops, laptops, and servers (x86_64)
Self-install Image (1.4 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Preconfigured Image (raw) (1016.0 MiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Fully Encrypted Disk Image (raw) (2.3 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Preconfigured Image (qcow) (1.3 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
VMware (2.3 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Packages Image (1.7 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
UEFI Arm 64-bit servers, desktops, laptops and boards (aarch64)
Self-install Image (1.3 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Preconfigured Image (raw) (951.3 MiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Preconfigured Image (qcow) (1.2 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación
Packages Image (1.3 GiB)
Download
Metalink Escolla un servidor de réplica Suma de comprobación

Escoller que medio descargar

The new self-install image is the goto choice for USB or DVD based installations. A simple self-install wizard dumps a preconfigured image to the drive, and grows the partition to the size of the disk.
Users with Raspberry Pi and similar without usb-boot support can directly write the pre-conifgured image to the SD card. Users seeking more control over deployment are advised to use Combustion.
A demo of a combustion based deployment can be seen here.
The jeos-firstboot will greet those who did not configure their system by using Combustion.

Leap Micro no longer comes with a traditional installer, users shall use Self-install media instead. The new Packages Image is just an offline dump of Leap Micro rpm repository for those with isolated enviornment.

Documentación

Mínimo

  • Memoria: 1GB RAM física + memoria adicional para a súa carga de traballo
  • Almacenamento:
    • Partición / (root): 5GB de espazo dispoñible en disco
    • Partición /var: 5GB de espazo dispoñible en disco

Recomendado

  • Memoria: 2GB RAM física + memoria adicional para a súa carga de traballo
  • Almacenamento:
    • Partición / (root): 20GB de espazo dispoñible en disco
    • Partición /var: 40GB de espazo dispoñible en disco

Comprobe a súa descarga antes de usar

Moitas aplicacións poden verificar a suma de comprobación dunha descarga. Para verificar a túa descarga pode ser importante xa que verifica que realmente obtiveches o ficheiro ISO que querías descargar e non unha versión corrupta.

Para cada ISO, ofrecemos un ficheiro de suma de comprobación coa súa correspondente suma SHA256.

Para máis seguridade, podes usar GPG para verificar quen firmou estes ficheiros .sha256.

Debera AD48 5664 E901 B867 051A B15F 35A2 F86E 29B7 00A4

Para ter máis axuda de como verificar a túa descarga, por favor le Axuda sobre as sumas de comprobación