openSUSE Leap Micro 6.1

Leap Micro is an ultra-reliable, lightweight operating system built for containerized and virtualized workloads.

This community version is based on SUSE Linux Micro, which leverages the enterprise-hardened security and compliance components of SUSE Linux Enterprise. This merging of technologies provides for a modern, immutable, and developer-friendly OS platform.

Leap Micro since 6.0 offers a self-install image, a raw image, and a Packages DVD that can serve as an offline repository. The Self-install image is our recommendation for any USB-based installation since we no longer use traditional installers. Users can automate and customize their installation with either Ignition or Combustion or using the jeos-firstboot wizard. Give a try to Fuel Ignition our online Ignition config generator.

Try Leap Micro in VMs running on either Xen or KVM. Using a Raspberry Pi or other System on Chip hardware may use the preconfigured image. Both preconfigured and self-installed images are intended to be used with Combustion written to a USB, which is driven to allow configuration on any first boot, with the option for default password protected changes.

Download

Leap Micro 6.1 installation demo with a Full Disk Encryption and a two factor authentication in cockpit.

Intel or AMD 64-bit desktops, laptops, and servers (x86_64)
Self-install Image (1.4 GiB)
Preconfigured Image (raw) (1016.9 MiB)
Imaxe de disco completamente cifrada (raw) (2.3 GiB)
Preconfigured Image (qcow) (1.2 GiB)
Imaxe de paquetes (1.7 GiB)
UEFI Arm 64-bit servers, desktops, laptops and boards (aarch64)
Self-install Image (1.3 GiB)
Preconfigured Image (raw) (952.9 MiB)
Preconfigured Image (qcow) (1.2 GiB)
Imaxe de paquetes (1.3 GiB)

Escoller que medio descargar

The new self-install image is the goto choice for USB or DVD based installations. A simple self-install wizard dumps a preconfigured image to the drive, and grows the partition to the size of the disk.
Users with Raspberry Pi and similar without usb-boot support can directly write the pre-conifgured image to the SD card. Users seeking more control over deployment are advised to use Combustion.
A demo of a combustion based deployment can be seen here.
The jeos-firstboot will greet those who did not configure their system by using Combustion.

Leap Micro no longer comes with a traditional installer, users shall use Self-install media instead. The new Packages Image is just an offline dump of Leap Micro rpm repository for those with isolated enviornment.

Mínimo

  • Memoria: 1GB RAM física + memoria adicional para a súa carga de traballo
  • Almacenamento:
    • Partición / (root): 5GB de espazo dispoñible en disco
    • Partición /var: 5GB de espazo dispoñible en disco

Recomendado

  • Memoria: 2GB RAM física + memoria adicional para a súa carga de traballo
  • Almacenamento:
    • Partición / (root): 20GB de espazo dispoñible en disco
    • Partición /var: 40GB de espazo dispoñible en disco

Comprobe a súa descarga antes de usar

Moitas aplicacións poden verificar a suma de comprobación dunha descarga. Para verificar a túa descarga pode ser importante xa que verifica que realmente obtiveches o ficheiro ISO que querías descargar e non unha versión corrupta.

Para cada ISO, ofrecemos un ficheiro de suma de comprobación coa súa correspondente suma SHA256 e un ficheiro de sinatura con sinatura cifrada.

Para asegurar a integridade do ficheiro descargado pode usar sha256sum para verificar a suma de comprobación e gpgv para verificar a sinatura cifrada.

Debera AD48 5664 E901 B867 051A B15F 35A2 F86E 29B7 00A4

Para ter máis axuda de como verificar a túa descarga, por favor le Axuda sobre as sumas de comprobación